[C°]
Change this if, for example, you need to connect a wireless adapter to non-default port pins.The first serial port (-1 or 0) will always be used by the Arduino bootloader regardless of this setting.Enable this if your board has a secondary serial port.Serial port -1 is the USB emulated serial port, if available.The serial communication speed of the printer should be as fast as it can manage without generating errors. #endif
This option may be needed if your Z driver tends to overheat. #define I2CPE_DEF_TYPE I2CPE_ENC_TYPE_LINEAR
#if ENABLED(MIN_SOFTWARE_ENDSTOPS) #define RETRACT_RECOVER_LENGTH_SWAP 0 // (mm) Default additional swap recover length (added to retract length on recover from toolchange)
CoreXY uses a special belt arrangement to do XY motion, requiring a little extra maths.
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup//#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use//#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W#if ANY(BLINKM, RGB_LED, RGBW_LED, PCA9632, PCA9533, NEOPIXEL_LED) #define BABYSTEP_MULTIPLICATOR_Z 1 // Babysteps are very small. Reply About; Installation ; Features open dropdown menu. #define PROGRESS_BAR_MSG_TIME 3000 // (ms) Amount of time to show the status message Perhaps I have a mistake in configuration, so I want to try out your tool.
Add more offsets if you have 3 or more nozzles.This option allows the controller board to switch the power supply 12V on and off with Enable this if you don’t want the power supply to switch on when you turn on the printer. With this option, Some hosts use a proportional font in their output console. Du kannst dich mit deinem Konto #define JUNCTION_DEVIATION_MM 0.013 // (mm) Distance from real junction edge //#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point In the procedure known as “homing,” each axis is moved towards one end until the endstop switch is triggered, at which point the machine knows that the axis is at the endstop (home) position. Hello,his tool is working pretty well for me but if try to switch from 1.1.8 to 2.0 i get this error :please commit your changes or stash them before you can merge.
#define USER_DESC_3 "Preheat for " PREHEAT_2_LABEL Ganz eifach heute kaufen - morgen drucken.
#define HOTEND2_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor This can be pretty fast. 3DWare steht für 3D Druck in der Schweiz und hat als grösster Schweizer Online 3D Drucker und Filament auch die umfangreichste Auswahl von 3D Produkten in der ganzen Schweiz. #define COOLANT_FLOOD_INVERT false // Set "true" if the on/off function is reversed One common application for a servo is a Z bed probe consisting of an endstop switch mounted on a rotating arm. #define INVERT_E2_DIR false #define USER_GCODE_2 "M140 S" STRINGIFY(PREHEAT_1_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_1_TEMP_HOTEND) This option hides the SD card from the host PC.Use the optimizations here to improve printing performance, which can be adversely affected by graphical display drawing, especially when doing several short moves, and when printing on DELTA and SCARA machines.Some of these options may result in the display lagging behind controller events, as there is a trade-off between reliable printing performance versus fast display updates.The hardware watchdog should reset the microcontroller, disabling all outputs, in case the firmware gets stuck and doesn’t do temperature regulation.If you have a watchdog reboot in an ATmega2560 the device can hang forever, as a watchdog reset will leave the watchdog on. #define INVERT_Y_STEP_PIN false Until they reach a sufficient temperature, these sensors usually return the lowest raw value, and this will cause a Min Temp Error.To solve this issue, this option sets the number of milliseconds a hotend will preheat before Marlin starts to check the temperature.
[steps per mm] #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 } Homing and probing speeds are constrained by the current max feedrate and max acceleration settings.Setting these values too high may result in reduced accuracy and/or skipped steps. [mm]
Reply